What's in the box and the first charge

Based on the unboxings we have seen, the standard box contains the console, a USB-A to USB-C cable, a manual and the microSD card or cards in the capacity you chose. The contents can vary from batch to batch and are confirmed before you order. One thing worth knowing before you open it: no charger is included. Use a 5 V USB mains adapter supplying at least 1.5 A, for example your phone's plug if its specifications match, and connect the cable to the USB-C port marked DC on the bottom edge. There's no need to hunt for a powerful adapter: the label on the back states 5 V and 7.5 W.

The 4000 mAh Li-Po battery, whose capacity is printed on the rear label, deserves a full first charge before a long session. Battery life is up to 6 h announced by the manufacturer, and in practice this varies with brightness, volume, the emulator and the game. While it charges, look for the small status LED between Select and Start: how it behaves depends on the system, so treat it as a clue rather than a definitive reading.

Two card slots: TF1 for the system, TF2 for games

The console has two microSD slots, and their roles cannot be swapped. The TF1 slot, on the right-hand side, holds the system card: this is the one containing Linux, the menu and the emulators. The TF2 slot, on the left-hand side, takes the games card, the one you fill yourself. This split has a real practical benefit: you can remove, copy or replace the games card without touching the system. The figure to remember is a maximum supported capacity of 128 GB. A bigger card won't make the console any faster, it simply lets you store more games.

On the bottom edge you'll find three connectors: the USB-C port marked DC for charging, the 3.5 mm headphone jack in the middle and a second USB-C port marked OTG, intended for USB accessories depending on the firmware. Don't mix up the two USB-C ports: the DC port is the one for charging. On the sides, the Power and Reset buttons sit on the left and the volume rocker on the right. There is no HDMI output.

R36 Max hardware at a glance
PartLocationPurpose
TF1 slotRight-hand sideHolds the system card: Linux, menu and emulators
TF2 slotLeft-hand sideHolds the games card you fill yourself
USB-C DC portBottom edgeCharges the 4000 mAh battery with a 5 V adapter of at least 1.5 A
USB-C OTG portBottom edgeUSB accessories depending on the firmware, for example a Wi-Fi dongle sold separately
3.5 mm headphone jackBottom edge, centreConnects wired headphones or earphones
Power and Reset buttonsLeft-hand sideSwitch the console on and reset it if it freezes
Volume rockerRight-hand sideAdjusts the sound level

First start-up and a tour of the menu

First check that the system card is pushed fully into the TF1 slot, then press the Power button on the left-hand side. The console boots into a factory Linux image, ArkOS on some batches, with an EmulationStation-style interface. The fully laminated 4-inch square IPS screen, at 720 × 720 pixels, shows a sharp, easy-to-read menu. If the screen stays black, charge the console through the DC port for about 30 minutes and check the card is seated properly before trying again. Then set the brightness to a comfortable level: it's also one of the things that affects battery life.

The home screen lists the systems, which you scroll through with the D-pad before going into one to see its games. Depending on the firmware, a system with no games may not appear at all, so a short list at first is perfectly normal if the TF2 card is nearly empty. Sound and display settings and the shutdown option are in the main menu, and the button that opens it depends on the installed firmware.

The controls, from the D-pad to the football button

The front follows a classic layout. The D-pad is on the left and the four ABXY buttons form a diamond on the right: X at the top in blue, Y on the left in green, A on the right in red, B at the bottom in yellow. Two analogue sticks sit in the lower corners for games that use them. Between the D-pad and the buttons, the speaker grille is shaped like a little football pitch. On the back, four triggers, L1, L2, R2 and R1, line up above the sculpted grips, which sit neatly under your palms.

The Select and Start buttons are heart-shaped, with the status LED between them. The FN button, round and printed like a football, can spin under your finger. What it does depends on the installed firmware: any button combinations are described in that firmware's documentation. Take a few minutes to learn them before starting a long session, so you don't quit a game by accident.

Adding your own games from a computer

Start by switching the console off from the menu, then remove the games card from the TF2 slot on the left-hand side. Put it into your computer using a microSD card reader. If the card has already been prepared, it contains folders for the different systems, whose exact names depend on the firmware. Copy each file into the folder for the system it belongs to: a game in the wrong place won't be picked up by the right emulator. Only use games you have the right to use, such as indie titles freely distributed by their creators.

Eject the card safely on the computer, put it back in the TF2 slot and switch the console on again. If the new games don't show up, use the menu option to update the game lists, or restart the console. The R36 Max has no built-in Wi-Fi and no Bluetooth, so box art and descriptions aren't fetched automatically from the internet. A USB Wi-Fi dongle in the OTG port may work depending on the firmware; it is sold separately and online play is not guaranteed.

  • Switch the console off from the menu before removing the card.
  • Copy the games into the correct system folder on the TF2 card.
  • Eject the card safely on the computer.
  • Put the card back, switch on, then refresh the game list.

Saving your progress and shutting down properly

There are two ways to save. In-game saves, the ones the game already offered on its original console, record your progress at the points the game allows. Save states, on the other hand, freeze the exact moment you're at, but whether they're available and how they work depends on the emulator you're using. Get into the habit of using the game's own save when there is one, then quitting back to the menu before switching off, so the file is properly written to the card.

To switch off, use the shutdown option in the menu rather than cutting the power: an interruption during writing can corrupt the data on a card. It's also worth regularly copying the contents of both cards to a computer. Finally, the R36 Max sold here is the original square-screen model, not the R36 Max2, and we check the hardware revision of every batch before dispatch.

Frequently asked questions

Can the R36 Max be connected to a TV?

No. The console has no HDMI or TV output: you play only on its 4-inch square IPS screen. The connectors on the bottom edge are for charging, headphones and, through the OTG port, compatible USB accessories depending on the installed firmware.

Why does my card show less space than its stated capacity?

That's normal: after formatting, the usable space is always lower than the nominal capacity, whether it's a 64 GB or a 128 GB card. Choosing one or the other changes how many games you can store, not how the console performs.

Do 4:3 games look stretched on the square screen?

Displayed without stretching, a 4:3 game keeps its proportions on the 720 × 720 panel, with bars above and below the picture. The display options available depend on the system and the emulator, so explore the settings of the emulator in question rather than looking for one universal setting.

Should I install different firmware on the first evening?

There's no need: the console works with its factory Linux image. Community firmware does exist, such as versions of ArkOS for the R36 Max, but you install it at your own risk. If you decide to go ahead, back up the contents of both cards first so you can go back if needed.

Sources

Our guides are based on the supplier's product sheets and publicly available documentation. We don't claim any hands-on testing.